24/7 Emergency Plumbing4.9 stars on Google

Home Tips9 min read

Tankless water heater maintenance in Orange County: what hard water does, and how often to flush.

Eric Dean Olson

Eric Dean Olson

Licensed C-36 Plumbing Contractor

Key Takeaways
  • Tankless water heater maintenance is routine upkeep in Orange County, not a repair. Hard water leaves scale inside the heat exchanger, the part that heats the water as it passes through. A flush, also called a descale, clears it out.
  • Plan on a flush once a year. Rinnai, Navien, and Rheem each say at least that, and Rheem says about every six months where the water is hard.
  • A water softener or a conditioning system slows the scale down. It doesn't end the flushing. It can stretch the time between flushes.
  • The water is safe to drink. Scale is about the equipment.

You've probably already met your water. It's the white crust on the faucet and the spots on the shower glass that come right back after you clean them. The same minerals go through your water heater every day.

Here's what that does inside a tankless, how you'd know, and what tankless water heater maintenance looks like here, including how often it needs a flush.

And if yours hasn't been flushed in a while, you're in good company. There's no scolding on our end. Our water heater service guys flush and descale these every day.

What scale does inside a tankless water heater.

Heating water is what pulls the minerals out of it. In a tankless, that happens inside the heat exchanger, and the minerals stay behind as scale on its inside walls. Left alone, the scale slows the heating, narrows the path the water takes, and makes the heater work harder for the same shower.

A flush clears the scale out. It doesn't change the water that put it there.

Scale is the same lime and minerals that build up in a coffee maker. Navien makes that comparison itself.

In south Orange County, 2025 averages ran about 12 to 17 grains per gallon, depending on your district and the plant that feeds it. Rinnai's and Noritz's own charts both put water over 12 in their top class, which both call extremely hard. We list every district in our guide to Orange County water hardness by city.

Scale isn't a safety question. The water is safe to drink, and the districts and the county Grand Jury say so in plain words. This is about equipment.

Good to Know

On a tankless, a flush and a descale are the same job. Navien's own guide calls it "descaling (aka flushing)." Either word works when you call.

What we see in the field.

Our guys made 317 water heater flush and descale visits from January through October this year, nearly all of them on tankless units. Irvine was first with 88, then came Lake Forest with 54 and Mission Viejo with 35. Those are cities where we do a lot of work, so that shows where our calls come from, not whose water is hardest.

It's also the most common thing we do to a tankless. Looking back over six years of our jobs, close to half of our tankless service jobs were a descale (45.1%, when we counted this past August).

Why a tankless feels hard water differently from a tank.

Same water, two different machines.

What changesTank water heaterTankless water heater
Where the minerals end upThey settle to the bottom of the tank as sedimentThey coat the inside of the heat exchanger as scale
How much room they haveA whole tankNarrow waterways
How you find outRumbling or popping, sometimes less hot waterSlower heating, less flow, then a reminder or a code on the controller
The upkeepDraining and flushing the tankDescaling the heat exchanger

A tank has room to hide a lot of it.

Eric Dean Olson

I remember a call in Costa Mesa from a customer whose water heater wasn't lighting. It was only six years old, it had a 12-year warranty, and it wasn't leaking. It needed a new thermocouple, a small part at the pilot light. So a repair made more sense than a replacement, and I encouraged her to get the rest of the years out of it.

I usually ask a customer what maintenance looks like for their plumbing. She had never maintained the water heater. She didn't know she was supposed to. I was already at the house, so I offered to flush it as a courtesy. I grabbed my bucket, my hose, and my channel locks, and got started.

When I flush a water heater, I point the hose into a five-gallon bucket. Some people run the hose out to the grass or the driveway, and whatever comes out just floats down the street. I like to see it, and I like to show the customer.

I'm usually not shocked by what comes out, because I've seen it so many times. This one was special. About a quarter of my bucket filled up with what looked like little crushed seashells, white flakes and big crystals. I kept waiting for it to stop, and the clumps kept coming.

When I was done, I knocked on the garage door and asked her to come take a look. We both stood there amazed. I think she understands now why a water heater needs maintenance, and I hope I got her some extra years out of it.

A tankless has no room to hide anything. The water runs through narrow waterways, and the heater watches its own temperature and flow. So when scale builds, the heater tells you.

Neither one gets a pass in hard water. They show it differently. If you have a tank, sediment is one of the causes we cover in why a water heater leaks. If you're choosing a tankless, start with our Noritz, Rinnai, and Rheem comparison.

Signs of scale buildup in a tankless water heater.

Most plumbing problems start small, and scale is the best example we know. Here's the order the signs usually arrive in.

  1. The house shows it first. White, chalky calcium buildup on the faucets, the showerhead, and the shower glass. If it's on the outside, it's in the heater too.
  2. The hot water takes longer, or the temperature wanders. You wait longer for hot water, or it swings between hot and cold on you. Rheem lists both as signs of mineral buildup in the heat exchanger. Other parts can cause the same thing, so it takes a look to know.
  3. There's less flow on the hot side. Noritz ties that to mineral buildup inside the heat exchanger or clogged filters.
  4. The controller says something. Rinnai's SENSEI RX manual says an LC code means the unit "is beginning to lime/scale up and must be flushed," and Noritz units can show a service reminder for scale buildup. Scale also sits in the background of other codes, which is why it comes up in our guides to code 11 on Rinnai, Rheem, and Noritz units.
  5. The heater shuts itself off. Left long enough, scale can lead to error codes and shutdowns.
Eric Dean Olson
Expert Tip

A reminder or a scale code is the heater asking for a flush. Clearing it from the controller doesn't clear the scale.

What tankless water heater maintenance includes, and what happens during the visit.

There are several things we do on an annual maintenance visit. It's not just a flush. Sometimes the fan, the burner, and other parts need cleaning too. But the most common job is descaling the heat exchanger.

A flush, or descale, circulates white vinegar or a descaling solution through the heat exchanger to dissolve the scale, then rinses it out with fresh water. The makers' instructions all follow the same outline.

  1. Shut off and isolate the heater. The gas goes off and the service valves close, so the heater is cut off from the house plumbing.
  2. Hook up a small pump, two hoses, and a bucket to the service valves.
  3. Circulate the solution. The pump sends it from the bucket, through a hose, into the heater. It passes through the heat exchanger and comes back out to the bucket. Navien says at least 45 minutes. Noritz's procedure says an hour, and Rinnai's SENSEI RX manual says at least an hour.
  4. Rinse with fresh water. Rinnai's manual says five minutes. Noritz's procedure says three minutes or more. Navien says at least ten.
  5. Clean the inlet filter, the small screen where cold water enters the heater.
  6. Put the heater back in service and test it.
Tankless water heater with its cover off and two hoses connected to the service valves
  1. More than a flushSometimes we clean the fan, the burner, and other parts too. The most common job is descaling the heat exchanger.
  2. The red handleWhere the hot water comes out.
  3. The blue handleWhere the cold water goes in. These are the service valves, also called isolation valves.
  4. Our hosesA pump circulates descaling solution from the bucket, through the heat exchanger, and back to the bucket.
Cover off and hoses on the service valves: a tankless flush under way in Lake Forest.

One thing has to be there first: service valves. You'll also hear them called isolation valves, and both names are right. They let us isolate the tankless from the rest of the house, so we can service the heater without touching the rest of the plumbing. Noritz lists an isolator valve kit as required equipment, and Rinnai "strongly recommends" them. If a tankless was installed without them, they have to be added before it can be flushed.

When we do it, the flush is part of a fuller visit. Our guys clean the ignition and flame rods, check the gas pressure, look over the venting, flush the heat exchanger, and run the heater through a full cycle before they leave.

If you're wondering what a flush costs, just ask when you call.

Maintenance record sticker on a tankless water heater, with hoses on the service valves below
  1. The maintenance recordThe date of the last service goes on the sticker. Whatever you use, keep track of when the heater was last maintained.
  2. Hoses on the service valvesA small pump, two hoses, and a bucket hook up here.
Our service sticker on a tankless water heater in Lake Forest, with the date of the last maintenance written in.

What you can do yourself, and what to hand off.

Here's the honest split.

  • Keep the vent openings clear. That one's yours.
  • Clean the inlet filter if your manual shows you how.
  • Keep the record. Write down the date of every flush. A reminder on your calendar works. So does booking next year's visit ahead of time. A lot of plumbers also put a service sticker on the heater with the date on it. Whatever you use, know when the heater was last maintained.

Rheem's guide puts the vent check and the filter on the homeowner's list, and Noritz agrees on the filter.

The flush itself is where the makers split. Rinnai publishes a 13-step flushing procedure on its homeowner pages. The other three point you to a pro. Navien says you can do it if you have "the right equipment, materials and skills," then recommends hiring a professional, because a descale done wrong can damage the heater and cost you the warranty. Noritz says professional servicing is recommended for descaling, and Rheem says flushing the heat exchanger is best left to a licensed professional.

Anything on the gas side, the burner, or the wiring is a hand-off. Rheem says the same.

Warning

If you flush it yourself, use only what your heater's manual calls for. Rinnai's instructions say undiluted white vinegar and "never use chemical solutions of any kind." Some Noritz models also have a blue flush connector with steps of its own, so follow the owner's manual for your unit.

Annual maintenance is a little more than hooking up a couple of hoses. Some people forget the filters. They sit in different parts of the heater, and each one has to come out so the little basket can be cleared. Don't skip the little steps. They make a big difference.

Hand holding the inlet filter screen pulled from a tankless water heater's cold water inlet
  1. The water inletOpen, with the filter pulled out.
  2. The inlet filterSome people forget to pull the filters and clear out the little baskets. The little steps make a big impact.
The inlet screen pulled from a tankless water heater in Ladera Ranch, held beside the open water inlet.

How often to flush a tankless water heater.

Once a year. That's where the heater makers land for a home on hard water, and three of the four say "at least."

MakerWhat its own guidance saysWhere it says so
RinnaiFlush "at least once a year." Its SENSEI RX manual adds that hard water "may require a more frequent flushing schedule."Flushing page, SENSEI RX manual
NoritzIts manual chart lists once a year for home use in any water over 3 grains per gallon, when no water treatment device is installed. A 2025 Noritz post gives a looser range, every one to three years.Help center, maintenance guide, 2025 post
Navien"At least once a year," and more often with more minerals, a higher temperature setting, or heavy hot water use.Descaling guide
RheemAt least once a year, and "about every six months" in hard-water areas.Maintenance guide

Most south Orange County water sits in the top class on both the Rinnai and Noritz charts. So once a year is where we start here. Think of it as the floor.

A tankless always has to be maintained. How long you can go between flushes comes down to the water going into your pipes. If you know your water is very hard, and there's no whole house filtration and conditioning system ahead of the heater, it can be necessary to flush every six months instead of once a year. Follow your heater maker's guidelines on how often and how, and keep a record of every flush.

Eric Dean Olson
Expert Tip

Sometimes a tankless fails, and it isn't because the heater is bad. It's because of the water, and nobody kept up with the maintenance. The makers stand behind their warranties, and in my experience they want to see that the heater was maintained properly. Keep the records.

Not sure when yours was last flushed, or whether it has service valves? Tell us the brand and about how old it is, and we'll tell you what we'd expect to find. Call (949) 328-6002.

Schedule a visit

Can you put a descaling filter on a tankless water heater?

This one comes up on the phone. Yes, in a few forms. There are four ways to keep scale down, and they aren't the same thing.

What it isWhat it does about scaleWhere it goes
A regular flushClears out scale that has already built up. It doesn't change the waterAt the heater, on a schedule
A scale protection add-onA device made to reduce mineral scale buildupAt the water heater or on the main line
A salt-free conditioning systemConditions the water to reduce scale buildup, without a salt-based softenerWhole house, at the main line
A water softenerRemoves the hardness minerals from the waterWhole house, at the main line

The add-on is the closest thing to a descaling filter. It's a descaler or scale protection device that goes at the water heater or on the main line. It protects the tankless itself, not the whole plumbing system, so it isn't a whole house water treatment system. And installing one doesn't descale a heater that already has buildup, so the flush comes first. The heater makers point to their own versions: Noritz's chart names its ScaleShield, Rinnai's manual offers the Scale Cutter, and Navien has PeakFlow.

We're big fans of systems that treat the whole home. But when a homeowner isn't ready for a whole house system, we'll still put together a solution that protects the tankless itself. Either way, we want to set the heater up for success by protecting it from the water.

A salt-free conditioning system treats the whole house. The HALO 5 is one we install.

A water softener treats the whole house too. The HALO CK10 and the Evince TRUE are softeners we install, and some systems, like the Evince ELITE, both filter and soften.

A whole house water filter by itself is a different thing. A carbon-only filter is just that: filtration, with no scale conditioning.

Good to Know

The heater makers have a say here too. Rinnai's SENSEI RX manual lists a water softener or the Rinnai Scale Cutter as "required" once water is over 12 grains per gallon. Noritz's chart lists its ScaleShield or a water softener for any water over 3. Check the water quality page in your own heater's manual.

We install all of these, so take this as a plumber's description, not a ranking. Which one fits your house is its own guide: water softener, whole house filter, or reverse osmosis. The basics are on our water softener and water filtration system page. We also wrote a guide to HALO 5 and Evince water systems.

Does a water softener end the flushing on a tankless water heater?

No. A water softener or a conditioning system slows the scale down, so the flushes can be further apart. It doesn't end them.

A water softener for a tankless water heater brings the grains per gallon down. It's rare for one to get the water all the way to zero. A home can have soft water and still read 3 to 5 grains per gallon. Even that small amount, passing through a heat exchanger day after day, has an effect over time. Scale still builds up. It just doesn't build as quickly.

You may have heard it both ways, and we think we know why. Noritz's manual chart says a yearly flush "is required if a water treatment device is not installed." Read quickly, that sounds like a softener ends the flushing. But Noritz's own maintenance guide says a water softener "reduces the frequency" of maintenance. In Navien's maintenance guide, the word is "minimize." And Rinnai's SENSEI RX manual says that in hard water "the water must be treated and may require a more frequent flushing schedule."

And here's why it doesn't go to zero, as we see it.

  • A softener only protects the heater while it's working. If the salt runs low or the resin wears out, hard water goes straight through to the heater.
  • A conditioning system is built to reduce scale. Reduce isn't the same as remove.
  • The rest of tankless water heater maintenance isn't about hardness. The inlet filter, the rods, and the vent still need a look.

So with a softener or a conditioner, think of the flush as a check that stretches out, not a chore that disappears.

Eric Dean Olson
Expert Tip

With proper maintenance, a tankless water heater can get its full life, about 20 years in my experience. Without it, that can drop to 10 to 15.

Frequently Asked Questions

Once a year is where the heater makers land. Rinnai, Navien, and Rheem each say at least once a year, and Noritz's manual chart says once a year for hard water. Rheem says about every six months in hard-water areas. South Orange County water averaged about 12 to 17 grains per gallon in 2025, so once a year is the place to start here.

Not worse. Different. In a tank, the minerals settle to the bottom as sediment. In a tankless, they coat the heat exchanger as scale, and the heater tells you with slower heating, less flow, or a code. Both need regular upkeep in hard water.

Some folks do. Rinnai publishes a homeowner procedure. Navien, Noritz, and Rheem all recommend a professional for the descale itself, and Navien notes that a descale done wrong can cost you the warranty. Cleaning the inlet filter and keeping the vent clear are the usual homeowner jobs.

Check the water quality page in your heater's manual, because the makers answer this one themselves. Rinnai's SENSEI RX manual lists a water softener or the Rinnai Scale Cutter as required over 12 grains per gallon, and Noritz's chart lists a softener or its ScaleShield for hard water. A softener is one way to treat the water, not the only one. Either way, the heater still gets flushed.

Yes, in a few forms. A scale protection add-on goes at the water heater or on the main line to reduce scale buildup. A salt-free conditioning system or a water softener treats the whole house. If the heater already has buildup, a flush comes first.

The scale keeps building. Navien's own answer is that the buildup "can cause damage to your heat exchanger and may interfere with normal heating." The maker manuals we read also say damage from scale isn't covered by the warranty.

The Bottom Line

Orange County water is hard, and a tankless water heater is where it shows. Scale builds inside the heat exchanger, a flush clears it out, and the makers say to do that about once a year. A water softener or a conditioning system slows the scale down. It doesn't end the flushing.

Call (949) 328-6002 or schedule a visit, and we'll take a look with you. To see what your district's water runs, start with Orange County water hardness by city.

If it's been a while, that's fine. The best time was last year. The second-best is whenever you call.

Written by Eric Olson, Licensed C-36 Plumbing Contractor, Olson Superior Plumbing, Orange County, CA. CSLB license #1045399. Serving Orange County homes since 2008. Flush intervals come from each heater maker's own published guidance, read November 12, 2026. Hardness figures come from each water provider's 2026 water quality report, covering 2025.

Share this post

Eric Dean Olson

Written by

Eric Dean Olson

Founder & Chief Vision Officer, Licensed C-36 Plumbing Contractor, CA #1045399

Eric Olson is a Licensed C-36 Plumbing Contractor and Founder of Olson Superior Plumbing, where he's built a portfolio of home services businesses generating more than $25 million in annual revenue. With more than 18,000 homes served since founding the company in 2008, Eric brings real field experience to every article he writes — from water heater diagnostics to whole-home repiping. BBB A+ accredited. Top 5% of California contractors.

24/7 emergency plumbing & HVAC service

Call us anytime — day or night, weekends and holidays. Our team is always ready to help.

Schedule Service